NTK Oxygen Sensors
NTK Oxygen Sensors combines expertise with innovation and delivers Oxygen Sensors with superior fit, form and function. When you require the best, count on NTK Oxygen Sensors to deliver.
The oxygen sensor is used in multiple applications like Generators / 2W/3W/4W and other applications for controlling the exhaust emissions of petrol, diesel and gas engines with the help of ECU. It is an oxygen concentration sensor which measures the residual oxygen content of the exhaust gas and then transmits a signal to the engine control unit in the form of an electric voltage. The electric voltage allows the control unit to detect whether the mixture is too lean or rich. In order to bring the engine into the optimum operating range the control unit reduces the quantity of fuel in the A/F ratio, if the mixture is too rich and increases it if the mixture is too lean.
NTK oxygen sensors are OEM approved & fitted in Maruti Suzuki India Ltd., Honda Cars India Ltd., Fiat India Automobiles Ltd., Ford India Pvt. Ltd, Volkswagen India Pvt Ltd., Honda Motorcycle & Scooter India Pvt. Ltd., Hero MotoCorp Ltd., Honda India Power Products Limited (for Generators), etc. Being a most preferable product by OEMs our current market share is more than 60%.
OEM QUALITY AND RELIABILITY
Each NTK Oxygen Sensor is:
- Extensively Tested During Manufacture to Guarantee Quality and Reliability.
- Supplied With a Factory-Fitted OEM Connector for Easy Installation.
- Precision manufactured with a sensing element incorporating NTK’s premier technical ceramics.
Oxygen sensors should be tested at each tune-up. Failed or worn out oxygen sensors can cause:
- Failed Emission Tests
- Increased Fuel Consumption
- Failed Catalytic Converters
- Poor Drive-ability
- Increased Emissions
NTK oxygen sensors OEM customers in India | |
---|---|
Two-Wheelers | • Hero MotoCorp Ltd. • Honda Motorcycle & Scooter India Pvt. Ltd. • TVS Motor India Ltd. • Bajaj Auto Ltd. • Royal Enfield • Piaggio Vehicles Pvt. Ltd. |
Three-Wheelers | • Piaggio Vehicles Pvt. Ltd. |
Four-Wheelers | • Maruti Suzuki India Limited • Suzuki Motor Gujarat Pvt Ltd • Honda Car India Limited • Ford India Pvt. Ltd. • Volkswagen India Pvt. Ltd. • Fiat India Automobiles Ltd. • Mahindra & Mahindra • Skoda Auto Volkswagen India Private Limited • Renault-Nissan India Pvt. Ltd. |
Other Applications (Generators) | • Honda India Power Products Limited |
NTK oxygen sensors for After Market
Niterra India PVT. LTD. continues to deliver high Quality products that contribute to protecting earth’s environment, which should be passed on to our next generations. Hence we are launching NTK oxygen sensors in Indian After Market to cater a wide range of BS-6 Two Wheeler Scooters and Bikes. Our Zirconia oxygen sensors range are:
CONDITIONS WHEN OXYGEN SENSOR SHOULD BE REPLACED
1. BASED ON VEHICLE UNUSUAL BEHAVIOUR, WHEN
- MIL light turns “ON”
- Water goes inside the vehicle due to flood
- Vehicle met with an accident or get damaged
- Vehicle shows low fuel efficiency and acceleration
- Vehicle causes starting trouble/ unstable Idling
- Engine causing misfiring or poor pick up/ power
- Vehicle causes smoky exhaust, high pollution
2. BASED ON OXYGEN SENSOR APPEREANCE
Bending Sensor Body
Broken Lead Wire
Water Intrusion To Sensor
Melting connector
Clogging Holes
Carbon Deposits
Silicon Poisoning
Water Intrusion To Connector
NTK OXYGEN SENSOR SOCKETS FOR AFTER MARKET
- These sockets are specially developed for Oxygen sensors (OZAS-S5 & OZAS-S6).
- Can be used for all (M12 Dia sensors), which is majorly fitted in all the two wheelers.
- Good strength, can easily sustain the maximum torque limit (upto 50Nm).
- Easy to use on vehicle near engine/exhaust area.
- Its side groove protects the lead wire from damage.
AFTERMARKET PART NO :
- OSST001 – Torque wrench compatible
- OSSTL002 – L-Handle compatible
PRECAUTIONS
- Use the socket only for Oxygen Sensors.
- Don’t use it for loosening and tightening of any 17mm nuts or bolts else it may get damage.
- Use this socket with specified torque value (max up to 50Nm).
- Excess Force or Torque may damage the Socket/ Oxygen sensor or both.
- Oxygen Sensors should be tighten and loosen with the help of special Oxygen Sensor Sockets not from any Spanner.
Bending sensor body
Broken Lead Wire
Loosen Seal
* For Oxygen sensor tightening process, tightening torque limit and applications, refer the instruction manual provided inside the NTK (OZAS-S5 & OZAS-S6) oxygen sensor packs.